Carl-goldberg GBGA1044 Bedienungsanleitung

1INSTRUCTIONSWARNINGA radio-controlled model is not a toy and is not intended for persons under 16 years old. Keepthis kit out of the reach of younge

103.  Draw a line across the hinge line of the rudderand transfer the mark to the other side of therudder.  Using a 1\8” drill, drill half way throu

112  Slide the stab onto the aluminum tubes. Use the two #4x 1/2” screws to lock the stabin place. The blind nuts are already installed inthe fusela

ELEVATOR SERVOS1.  Collect the following items(2) Servos(2) 2-56 x 32” pushrods(2) 2-56 clevis(2) silicone clevis keepers(2) nylon swing in keepers2.

136.  You can bend the pushrod in the plane Makethe 90 degree bend and then cut the remain-ing wire off leaving a 3/8” length. With the pushrod rei

143.  Pull the cable tight and crimp the swage witha pair of pliers.4.  Slide the silicone keeper on the clevis.  Thread the clevis onto the riggin

15ENGINE INSTALLATIONThe Motor you choose may have a different typeinstallation as show. We show an O.S. 1.20 motor,this motor has more than enough po

16 Mark the location of the mounting holes on themounts. Remove the engine and drill a 1/8”hole at each location.  Mount the engine to the mounts us

173.  Mount the cowl in position and hold in placeusing masking tape. You will have to make acut out for the engine head on the bottom ofthe cowl. 

188.  Reinstall the cowl and transfer the hole loca-tion to the cowl. Throttle Servo Installation1. Collect the following items:(1) 2-56 x 18” thrott

196.  Attach the ez-connector to your servo arm. Put a drop of CA on the nut to make sure itdoes not come loose.7.  Insert the pushrod into the ez-

2Congratulations on your purchase of the67”Yak 54 ARF. Every effort has been made toproduce a lightweight, straight, easy to assem-ble aircraft. Becau

203.  Attach the fuel pickup line to one of thestraight tubes.  Attach the clunk to the other end. Fit assembly into the tank and adjust thelength

21Receiver and Switch Installation1.  The switch can be mounted in any convenientlocation. The sheeted part of the fuselage justbelow the sides work

22Final Assembly1.  Attach cowl using locktite on the screws.  Install muffler, needle valve, prop and spinner.wing bolt2.  Trial fit the wing tube

3ADHESIVES & GLUING TECHNIQUESCA adhesives are specially formulated to firmly glue theplywood, hardwood, and balsa used in your model and towithst

3.  Using a 1/8” drill, drill half way through theaileron hole from both top and bottom till thedrill passes through the aileron. Insert the 4-40 x

52.  Locate the pre-drilled aileron hinge holes inboth wing halves. Using a 3/16” drill, drill eachhole 1/8” deep. This will allow the center ofthe

63.  Attach the 12” servo extension to the servo.IMPORTANT! To ensure that any connections locat-ed inside the wing will not come loose, either when

74.  Bend the pushrod 90 degrees at the locationof your mark. Cut the remaining wire leaving 3/8”.3/8”5.  Install the nylon swing in keeper to atta

WHEEL AND WHEEL PANTS1. Collect the following items:(2) 5-32 x 1-1/4” Axle with Locking Nut(4) 5/32 Wheel Collars(6) 6-32 x 1” Cap Screws(2) 4-40 Blin

94. Install the blind nut in the wheel pant using the 4-40 bolt to pull it into the hole.Wheel CollarsWheel PantWheelLanding Gear5.  Mount the wheel