INSTRUCTIONSWelcome to the world of Ultimate flying! Now that you're an experienced R/C pilot, you're ready to step up toa higher level of
3. Locate the pre-cut stab cutout by feelingalong the fuse side in the area where thestab should go. Remove the covering over the stab slot onboth
9. When the stab is correctly aligned, outline onboth the top and bottom of the stab where itmeets the fuse, as shown. 10. Remove the stab from th
15. When dry, turn the fuse over and wick a fewdrops of thin CA gluet along the stab/fusejoint.Control Horn Installation1. Collect the following p
Landing Gear Installation1. Collect the following items:(1) Landing gear(3) 6-32 x 3/4” socket head screws(3) 6-32 blind nuts(3) #6 washers(1) Fusel
Tailwheel Installation1. Collect the following items:(1) Tailwheel bracket(1) Tailwheel(2) Springs(2) 2-56 x 1/2” Philips head screw 2. Locate the
Align MarksREMEMBER, the following pictures and instruc-tions may vary slightly, depending on the equipmentyou are using.2. Using the alignment mark
16Elevator Pushrod Installation1. Collect the following items:(3) .072 x 10” threaded wire(3) Nylon snap link(1) Single-hole pushrod plug(1) Double-
12. When the bent tip is exiting the hole in thepushrod and the plug tightly meets thepushrod, apply CA glue to the joint.13. Insert both of the n
16. Thread the snap-links onto each of the wires,until the the wire shows in the middle of thesnap-link.17. Connect the snap-link to the second hol
5. Place the cockpit insert on the fuselage and,while pressing down on the insert, tape thecockpit insert down.6. Using a 1/16” bit, drill four hol
ITEMS NEEDED TO COMPLETE THIS AIRCRAFT 1 RADIO GUIDANCE SYSTEM (4 CHANNELMINIMUM REQUIRED) 2 12” AILERON SERVO EXTENSION WIRES 1 Y-HARNESS 1 ENGI
2. Mark 1/4” from the end of the .063 wire andmake a 90º bend.3. Cut the wire to a length of 12-3/8”.4. Cut off a piece of nylon guide tube 9-1/2
2. Check to see if any part of the engine muffleror exhaust header will interfere with the fuse-lage. If necessary to create clearance,remove a por
. Place a piece of masking tape down the cen-ter of the wide yellow trim stripe. Measuring up 1-3/8” from the bottom of theyellow stripe, make two
10. Measure 2-7/8” from the landing gear blockon both sides of the front former. Glue thefuel tank support stick across the opening theformer.3.
11. Reach into the fuselage and place the fueltubing onto the brass fuel tank tubes. Notewhich tube is the vent and which is the outlet.12. From th
NOTE: There are several ways to mount wheelpants. Following are two different methods.4. Place the wheel pant against the back of theaxle, next to th
1. Collect the following items:(1) Bottom wing(1) Top wing(1) Bottom wing bolt plate(2) I-struts(8) 4-40 x 1/2” sock head screw(8) 4-40 blind nut(8)
4. Connect the aileron coupler assembly to theaileron control horns, as shown.7. Working from the outside (towards the fuse-lage) insert the 4-40
Decal InstallationSpinner Assembly1. Clean model surfaces thoroughly beforeapplying decals. 2. Cut decal sheets apart in sections, as need-ed. F
Fully-charged flight batteriesRadio transmitter1 ½ volt starting battery & glo-plug clipFuel bulb or pumpTools for tightening any parts that can
INTRODUCTIONUSING THIS INSTRUCTION MANUALBefore you begin assembling your ULTIMATE ARF, takesome time to read through this entire instruction book. I
Developing your flying skills to include more variedmaneuvers is exciting and rewarding.. The ULTI-MATE is an extremely capable aircraft and is able
1. Collect the following parts:(1) Top Wing(1) Bottom Wing(4) Ailerons(16) Jet HingesWING CONSTRUCTIONAileron Installation2. Locate the pre-cut ai
8. Place the servo door on the wing and drill a1/16” hole on each corner. Screw the door tothe plate, using the #2 x 3/8” screw and the#2 washer sup
Aileron Extension Installation1. Gather the following items.(2) 12” extension wiresNOTE: Before starting, remove the servo door andmake sure the len
Wing Dowel Installation5. Thread a snap-link on the end of one of the1/16 x 7” threaded rods. Place the snap-link in the second-from-the-top hole o
1. Collect the following parts.(1) Fuselage(1) Servo tray(2) Front cabane doubler(2) Cabanes(2) Cross brace(4) 4-40 x 1/2” Socket head screw(4) 4-40
2. Locate the pre-cut hinge slots and, using ahobby knife, make sure all slots in the stabi-lizer, elevators, rudder, and fin are cleanlycut. Test
Kommentare zu diesen Handbüchern