Carl-goldberg GBGA1023 Bedienungsanleitung PDF herunterladen

CChhiippmmuunnkk

WARNING

A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep

this kit out of the reach of younger children, as it contains parts that could be dangerous. A radio-

controlled model is capable of causing serious bodily injury and property damage. It is the buyer's

responsibility to assemble this aircraft correctly and to properly install the motor, radio, and all other

equipment. Test and fly the finished model only in the presence and with the assistance of another

experienced R/C flyer. The model must always be operated and flown using great care and common

sense, as well as in accordance with the Safety Code of the Academy of Model Aeronautics (5151

Memorial Drive, Muncie, IN 47302, 1-800-435-9262). We suggest you join the AMA and become prop-

erly insured prior to flying this model. Also, consult with the AMA or your local hobby dealer to find an

experienced instructor in your area. Per the Federal Communications Commission, you are required

to use only those radio frequencies specified "for Model Aircraft."

LIMITED WARRANTY

Carl Goldberg Products, Ltd. has inspected and certified the components of this aircraft. The company urges the buyer to perform

his own inspection, prior to assembly, and to immediately request a replacement of any parts he believes to be defective for their

intended use. The company warrants replacement of any such components, provided the buyer requests such replacement with-

in a period of 10 days from the date of purchase and provided the defective part is returned, if so requested by the company.

No other warranty, expressed or implied, is made by the company with respect to this kit. The buyer acknowledges and under-

stands that it is his responsibility to carefully assemble the finished flying model airplane and to fly it safely. The buyer hereby

assumes full responsibility for the risk and all liability for personal or property damage or injury arising out of the buyer's use of the

components of this kit.

CARL GOLDBERG PRODUCTS, LTD.

P.O. Box 818 Oakwood GA 30566 Phone #678-450-0085 Fax # 770-532-2163 www.carlgoldbergproducts.com

400

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - CChhiippmmuunnkk

CChhiippmmuunnkkWARNINGA radio-controlled model is not a toy and is not intended for persons under 16 years old. Keepthis kit out of the reach of you

Seite 2

10Tail Wire1.  Collect the following parts:(1) Fuselage(1) Tail Skid Wire(1) 2mm x 3mm Sheet Metal Screw2.  Insert the end of the tail skid wire int

Seite 3 - Caution:

112.  Mount the elevator and rudder servo asshown above. Attach the EZ connectors to the servo armsthe same way you did the aileron servos. Insert

Seite 4 - JOINING THE WING

12BalancingYour model should balance 2-1/2” back from the leading edge ofthe wing next to the fuselage.Control Set UpTurn on your transmitter and plu

Seite 5 - Aileron Servo Extensions

2USING THIS INSTRUCTION MANUALBefore you begin assembling your Chipmunk 400 ARF,take some time to read through this entire instruction book.It is desi

Seite 6 - Fuselage Hatch

3ITEMS NEEDED TO COMPLETE THIS AIRCRAFT 1 4 CHANNEL RADIO WITH 4 MICRO SER-VOS. (WE USED 4 CHANNEL FUTABARADIO WITH S3108 SERVOS AND GREATPLANES ELEC

Seite 7 - Elevator Installation

4WingJOINING THE WING1.  Collect the following items:(1) Right wing(1) Left wing(1) Wing joiners(2) 5mm x 17 dowelA book or block of woodNOTE: If the

Seite 8 - Fin & Rudder Installation

5Installing Ailerons1.  Collect the following parts:(1) Wing(2) Ailerons ( Left & Right)(6) Mini CA hinges1.  Locate the pre-cut aileron hinge s

Seite 9 - Wheel Pants

62.  Remove the covering on the aileron wherethe control horn sits. Using CA glue, attach the control horn to theaileron.4.  Find the small aileron

Seite 10 - Installing Cowl

7Stabilizer1.  Collect the following parts:(1) Fuselage(1) Stabilizer & Elevator(1) wing(1) 4-40 x 1/2” Socket Head Bolt(1) Wooden Washer covered

Seite 11 - Battery Installation

83.  Insert the mini hinges into the slots in the ele-vator. Take the long wire pushrod and insert the “Z”bend end into the outer hole of the contro

Seite 12 - Balancing

9Landing Gear1.  Collect the following parts:(1) wing(2) Main Landing Gear Wire(4) 2mm x 6 Sheet Metal Screw2.  Remove any covering over the landing

Kommentare zu diesen Handbüchern

Keine Kommentare

Carl-goldberg GBGA1023 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Luftausrüstung Carl-goldberg GBGA1023 herunter. Carl Goldberg GBGA1023 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Luftausrüstung Carl-goldberg GBGA1023