1INSTRUCTIONSWARNINGA radio-controlled model is not a toy and is not intended for persons under 16 years old. Keepthis kit out of the reach of younge
1012. Remove the rudder and align the control hornon the mark you made. Make sure the holesfor the clevis are over the hinge line. Mount the contro
11NOSEGEAR INSTALLATION 1. COLLECT THE FOLLOWING PARTS(1) Nosegear strut(3) Wheel Collars and set screws(1) Wheel(1) Nosegear steering arm(1) 1.5mm
12ENGINE INSTALLATION 1. COLLECT THE FOLLOWING PARTS(1)ENGINE(4) #6 X 3/4SHEET METAL SCREWS(1) MOTOR MOUNT PLATES(1) SPINNER2. Find the Motor mount
4. Mark the location of the engine mountingholes. Also at this time mark the location of wherethe throttle pushrod should exit the firewall. Remov
4. Make a 1/4” bend at the end of the throttlepushrod and connect the push rod to thethrottle arm on the motor. Slide a swivel keeper in place over
15PUSH ROD INSTALLATION1. Collect the following parts(2) 19” Wood dowels(2) 1.5mm x 25cm wire(2) 1.5mm x 25cm threaded wire(2) Metal clevis(4) shrin
16RUDDER PUSHROD1. Remove the metal clevis from the end of a 1.5x 25cm wire.Threaded end8”1/2”2. Measure, starting from the threaded end, back8”
175. Tape the rudder so that it stays in the neutralposition. Align the servo arm so that it is sitting at 90degrees to the servo. Mark the locati
181. GATHER THE FOLLOWING ITEMS(1) FUEL TANK(1) RUBBER TANK STOPPER(1) CLUNK(1) 3MM X 25MM SCREW(1) CAP WASHER LARGE(1) CAP WASHER SMALL(1) 3MM X40M
19INSTALLING FUEL TANK1. Insert the fuel tank through the wing saddlearea and feed the fuel lines through the hole inthe firewall. Slide the tank a
2Parts List (Items Shown)Hardware List(Not Shown)1. Fuselage2. Wings with Ailerons3. Stab with Elevators4. Fin5. Rudder6. Tank Hatch7. Dihedral Brace8
20 Using artist's acrylics or modeling enamels,paint the pilot to suit your fancy. WARNING:Do not use lacquer-based paints, which willdestroy th
21FLYING YOUR SR. FALCON ARFGETTING READY TO FLYBEGINNING AEROBATICSTaking time here really pays off later. Rushing the set-up and testing frequently
3ITEMS NEEDED TO COMPLETE THIS AIRCRAFT 1 RADIO GUIDANCE SYSTEM (4 CHANNELMINIMUM REQUIRED, 5 STANDARD SER-VOS ) 1 Y-HARNESS 1 ENGINE .40-.46 2-CY
4COVERINGThe Sr.Falcon ARF is covered in a premium polyester filmchosen by many of the world's top flyers for its beauty,toughness, and ease of
5WING ASSEMBLY & INSTALLATIONAILERON INSTALLATION1. Collect the following parts:(1) Left wing(1) Right wing(1) Left aileron(1) Right aileron(8) C
61. Holding the wing joiner with the angle cutfacing up, insert them into the joiner pocketsin both wing halves. The joiner should fit eas-ily in th
AileronAILERON CONTROL HORN INSTALLATION1. Collect the following items(2) Large control horn with back plate(4) 3/4" screw(2) Metal clevis(2) 10
Mark wireSTAB & ELEVATOR INSTALLATION1. Collect the following parts:(1) Stabilizer(2) Elevator(1) Wing/fuse assembly(6) Jet hinges(1) Fin and Ru
97. Remove the covering inside the line you drewon the stab also.5. Epoxy the fin to the stab making sure it isperpendicular.6. Place the stab o
Kommentare zu diesen Handbüchern